
Vol. 7, Issue 2 (2018)
Science & Cycling Congress, 4/5 July, Nantes (France)
November 2018
Pages 1–61
Book of Abstracts of the Science & Cycling Congress
Book of Abstracts
-
A pedaling force vector can be represented by the sum of three elemental force vector waveforms.
Background & Purpose:
In recent years, we have become able to accurately measure the pedaling force vector using pedaling analyzer (Bikefitting.com, Sittard, Netherlands) or pedaling monitoring (Pioneer Corporation, Kawasaki, Japan) systems. Using these devices, mechanical pedaling characteristics can be calculated from the pedaling force vector and expressed as an efficiency index or torque effectiveness, which is also calculated from the tangential force profile during pedaling. However, these indicators only demonstrate the mechanical characteristics of pedaling and are not based on body movement. Hence, we aim to analyze the pedaling force vector waveform based on biomechanical pedaling motion. A previous study analyzing the EMG signals of the lower limb muscles demonstrated that, in trained cyclists, pedaling is accomplished by combining three similar muscle synergies. (Is interindividual variability of EMG patterns in trained cyclists related to different muscle synergies? J Appl Physiol, 108(6) 1727-36. 2010).
This study expresses the pedal force vector waveform obtained from the pedaling force analyzer system by the sum of element force vector waveforms.
Methods:
Two participants (a former professional and a top-level amateur cyclist) were given a variety of pedaling conditions (load: 100, 200, 300 W; cadence: 70, 90, 110 rpm; saddle position: back (5 mm), forward (10 mm), up (3 mm), and down (5, 10 mm); pedaling action type: normal, spinning, pulling and pushing and pulling). Pedaling force vector data was obtained every 15 degrees using a pedaling analyzer system (Bikefitting.com). Pedaling vector data were expressed as the sum of elemental vectors. Common elemental vector waveforms and parameters were determined so that the root mean square error between the sum of the elemental vector waveforms and the original vector data were minimized by changing the amplitude and phase difference. The pedaling vector data and parameters can be expressed numerically with the following equation:
.
Results & Discussion:
The force vector component in the tangential direction can be represented by the sum of two waveform components, excluding the constant average force, as shown in Figure 1. At this time, the shapes of the wave functions (f1: 1st and f2: 2nd component) are fixed; only their amplitude and phase angle change. In contrast, the radial direction of the vector component can be represented by the sum of three waveforms: two correspond to the amplitude and phase angle of the two waves expressed in the tangential direction, and the remaining one has an independent amplitude and phase angle.
The scatter diagram in Figure 2 was created using A1 and A2, which are the amplitudes of the 1st and 2nd component of functions obtained by resolving the vector component of the tangential direction. Using this scatter diagram, we can classify pedaling characteristics.
This result indicates that pedaling action can be represented by up to three elemental motions, which may correspond to muscle behavior expressed by three synergies. Importantly, this study accounted for the waveform’s phase angle change. In the future, we will investigate the difference between change in the element waveform and muscle force assessment, and will study the corresponding muscle force strength and pedaling action.
Conclusion:
Pedaling force vector components in the tangential and radial directions, obtained by a pedaling analyzer system, can be represented by the sum of two or three elemental waveform components, respectively.
-
Null effects of tDCS over the Left Prefrontal Cortex on Self-paced Exercise and EEG
Purpose: to test the hypothesis that transcranial direct current stimulation (tDCS) over the left dorsolateral prefrontal cortex (DLPFC) influences performance in a 20’ self-paced exercise and electroencephalographic (EEG) oscillatory brain activity in a group of trained male cyclists.
Methods: We conducted a pre-registered (https://osf.io/rf95j/), randomised, sham-controlled, within-subject design experiment. 36 trained males cyclists, age 27 (6.8) years, VO2max: 54 (6.13) ml/min/kg, completed a 20’ self-paced exercise in three separate sessions, under three stimulation conditions: anodal, cathodal and sham. TDCS was delivered for 20' before each test at a current intensity of 2.0 mA. The anode electrode was placed over the DLPFC and the cathode over the shoulder. We measured the power output, heart rate, RPE and EGG (at baseline and during exercise).
Results: The were not difference in power output (F = 0.031 = 0.31, p > 0.05) during the self-paced exercise between conditions: Anodal (235 W [95%CI 222 - 249 W]; Cathodal (235 W [95%CI 222 - 248 W] and Sham (234 W [95%CI 220 - 248 W]. Neither the heart rate, RPE nor EEG activity were affected by the tDCS (all Ps > 0.05).
Conclusions: tDCS over the left DLFC did not affect self-paced exercise performance in trained cyclists. Moreover, tDCS did not elicit any change on EEG activity either at baseline or during exercise. Our data suggest that the significant effects of tDCS on endurance performance (and at rest) reported by recent studies should be taken with caution.
Acknowledgments
This project was supported by grants from from the Spanish Ministerio de Economía, Industria y Competitividad-PSI2016-75956-P- to Daniel Sanabria and Mikel Zabala, a predoc-toral grant from the Spanish Ministerio de Economía, Industria y Competitividad (BES-2014-069050) to Luis Ciria, and a Spanish “Ministerio de Educación, Cultura y Deporte” predoctoral grant (FPU14/06229) to Darías Holgado.
-
Data Driven Bike Fitting
During bike fitting sessions, the optimal cyclist’ position is determined. Finding this optimal cycling position is often a time-consuming and labor-intensive process, i.e., a standard bike fitting procedure takes at least two hours when done by an expert bike fitter. The best position is a combination of comfort, performance and injury prevention. To get to this optimal position, a series of adjustments are made to the bike configuration. To date, however, bike fitting suffers from expert subjectivity as there is no consensus among bike fitters on which parameters to focus on. In order to examine this hypothesis about expert subjectivity, a reproducible test methodology is currently under development to perform and evaluate a bike fit by a group of independent experts in Flanders. Results of these tests will be discussed during the presentation
-
The new Exposure Variation Analysis (EVA) method to compare pacing strategy and performance during professional time-trial competitions
Abstract:
Several studies underlined the impact of pacing strategy on cycling time-trial performance. It has been reported that under steady environmental conditions, maintaining a constant power output (PO) is the most efficient strategy to improve performance (Wells et al. 2013). The Exposure Variation Analysis (EVA) method has recently been proposed to evaluate these pacing strategies, quantifying for an optimal constant pacing strategy the times spent at an accurate PO (APO), at an inappropriate PO (IPO), and the short-time regulations of inappropriate PO (REG) (Ouvrard et al. 2017). It has been demonstrated that increasing time spent at APO and decreasing time spent at IPO allows cyclists to develop higher mean PO and improve performance (Ouvrard et al. 2018. Under review). However, as these indexes are influenced by time-trials course, they were never used to monitor pacing strategies and performance for several time-trials performed by the same cyclists yet. The aim of this study was to analyse the relationships between changes of performance, mean PO and EVA pacing parameters in two professional cyclists during seven official competitive time-trials.
Methods: PO were collected for two professional cyclists (mean VO2max 79.0 ± 8.5 mL.min-1.kg-1) during the seven-same time-trials (performed between April 2013 and June 2017 and ranged from 18.7 to 51.6 km). PO fluctuations were analysed from EVA to quantify times spent at APO (PO between 90 and 110 % of mean time-trial PO), IPO (PO lower than 90 % or higher than 110 % of mean PO for more than 10 s) and REG (PO lower than 90 % or higher than 110 % of mean PO for less than 10 s). Relationships between ΔmeanPO (differences between subject 1 and subject 2 mean PO for each time-trial) and ΔmeanPO% (differences between subject 1 and subject 2 mean PO, each expressed as a percentage of the subject’s record PO on the time trial duration) and ΔAPO (differences between subject 1 and subject 2 times spent at APO), ΔIPO (differences between subject 1 and subject 2 times spent at IPO), and ΔREG (differences between subject 1 and subject 2 REG) were assessed thanks to Pearson correlation coefficients.
Results: ΔmeanPO ranged from -24 to +39 W for similar physical potentials (20-min record PO 432 vs 428 W). A trend to a negative relationship was identified between ΔmeanPO and ΔIPO (r = -0.70, p = 0.08). Stronger and significant relationships were identified between ΔmeanPO% and ΔIPO (r = -0.94, p = 0.002) and ΔAPO (r = 0.86, p = 0.01, Figure 1).
Discussion: The main finding of this study is that, when comparing two cyclists during several time-trials, changes of EVA pacing parameters were related to changes of cyclists’ ability to develop high mean PO. The more the cyclists were able to decrease their time spent at IPO and increase their time spent at APO, the more they had a maximal use of their physical capacity during the time-trial, allowing them to develop higher mean PO expressed as a percentage of their record PO. These results are in accordance with Wells et al. (2013), who demonstrated that maintaining a constant PO, and thus increasing time spent at APO, is optimal for time-trial performance under steady environmental conditions. Conversely, increasing PO variations, and consequently time spent at IPO or REG, reflect poor adherence to constant speed, increasing biomechanical losses or fatigue.
Conclusion: EVA seems to be a valuable method to monitor pacing and performance changes for two cyclists during several time-trials. Values of times spent at IPO and APO can be compared between cyclists to determine if their pacing strategy were optimal to achieve the best performance possible.
-
First evaluation of an automated system for cyclist’s aerodynamic drag assessment
Context: When riding on a flat road at high speed, the major part of the resistive forces experienced by a cyclist is due to aerodynamic drag. Reducing this drag is thus a key challenge for improving cycling performance. To do so it must be adequately quantified. In this regard, different methods have been proposed in literature: wind tunnel [1], dynamometric measurement [2], deceleration [3], and linear regression [4]. Recently, a new approach that couples 3D digitization and computational has been investigated [5-8].
-
Muscle deoxygenation during moderate- and severe-intensity cycling in youth elite-cyclists
Background: Near-infrared spectroscopy (NIRS) is a well-established technique to measure tissue oxygenation and haemodynamics during exercise. While muscle oxygen consumption is derived by measuring concentration changes of oxygenated and deoxygenated haemoglobin and myoglobin (O2Hb and HHb), total haemoglobin (tHb = O2Hb + HHb) reflect blood volume and perfusion. In particular, the change in HHb is considered a proxy for oxygen extraction at the muscle level during exercise and arterial occlusion, where the rate of reoxygenation has been used as a measure of mitochondrial function (Ryan et al, 2012: Journal of Applied Physiology, 113, 175-183). NIRS-derived signals therefore reflect the dynamic balance between oxygen delivery and utilisation and may be important measures to monitor training induced adaptations of aerobic function in skeletal muscle. However, current literature is scarce regarding reliability measures, especially in young athletes, which needs to be established to interpret changes with confidence.
Purpose: To assess the test-retest reliability of HHb-changes during moderate- and severe- intensity cycling, and during arterial occlusion in youth elite-cyclists.
Methods: Fifteen cyclist (mean ± SD: age 13.5 ± 1.8 y; stature 163.2 ± 12.2 cm; body mass 51.3 ± 12.4 kg; O2max 62.1 ± 4.2 mL.min-1.kg-1) completed two 6-min rest-to-work transitions (T) from baseline (BL: 60 W) to moderate- (90% of the first ventilatory threshold [VT1]: 120 ± 26 W) and to severe- (50% between VT and maximum power [Delta50]: 204 ± 43 W) intensity cycling. The transitions were interspersed by 8 min BL cycling. After Delta50 cycling, an occlusion was applied on the proximal thigh at a pressure of 300 mmHG until a levelling-off of the HHb signal was observed (3-5 min). The protocol was repeated after a passive rest of 1 h. Changes in HHb were measured on the belly of the right vastus lateralis muscle with a portable continuous-wave NIRS device at a sampling rate of 5 Hz (PortaMon, Artinis). Second-per-second data, were corrected for blood volume changes and normalised to the full functional range measured during the occlusion (0-100%). HHb changes (%) were calculated from BL to the maximum of VT1 (ΔBL-VT1) and from BL to the maximum of Delta50 (ΔBL-Delta50). In addition, the reoxygenation after occlusion was assessed with the slope of linear regression analysis (%.s-1). A typical example of the HHb signal is shown in Figure 1. Absolute and relative reliability was calculated with Bland-Altman statistics ± 95% limits of agreement and the coefficient of variation (CV; %), respectively. Paired t-tests were used for comparisons.
Results: The ΔBL-VT1 was 20.5 ± 11.7 and 21.6 ± 12.3% during T1 and T2, respectively (p = 0.079). The bias was 1.1 ± 2.3 % (95% LoA: -5.6 – 3.3) and the CV 10.1% (7.3 – 16.4). The ΔBL-Delta50 were 58.1 ± 9.6 (T1) and 56.5 ± 9.3% (T2) (p = 0.133) and the bias and CV were 1.6 ± 3.9% (-6.0 – 9.3) and 5.4% (3.9 – 8.6), respectively. The reoxygenation slopes were 7.2 ± 2.0 (T1) and 7.6 ± 2.1 %.s-1 (T2) (p = 0.053) with a bias and CV of 0.4 ± 0.7 %.s-1 (-1.8 – 1.0) and 7.0% (5.1 – 11.2), respectively.
Discussion: The present study quantified reliability for NIRS-derived changes in HHb during cycling at moderate and severe intensity as well as for reoxygenation after occlusion. The provided levels of 5.4% for severe-intensity cycling and 7.0% for the reoxygenation slope, are well below the level of 10% considered as acceptable for a measurement, and the level of 10.1% for moderate-intensity cycling is only marginally higher. The reliability data established, provide limits within which training induced adaptations may be interpreted with confidence. Longitudinal studies in young athletes could potentially benefit from these findings since the magnitude of changes in NIRS variables is probably greater than the reported measurement error. -
Connection between Heel Motion and Torque in crank revolution
In cycling, Torque is made from pedaling. Recently some power meters measure torque in pedaling. Especially Pioneer Power Meter (Pedaling Monitor System - Pioneer Corporation, Tokyo Japan) can measure torque and power in 12 zones in each crank revolution. Using this system, we can easily learn every torque pattern of cyclists are different. Furthermore, we already know ever pedaling of cyclists are different, some of these cyclists have different pedal motion in Left and Right, their L/R balance are different. While in pedaling, forefoot is fixed with cleat, vertical heel motion relative to the pedal angle. From these observations, we can make an assumption that heel motion affects torque. So, this research is carried out in order to find out which heel motion increase torque in a crank revolution.
-
Machine learning and physical modelling: optimizing the performance and strategy for time trials
Despite well-established equations and modern computational capabilities, physical modelling is only beginning to be used in cycling. Such theoretical approach allows to estimate the effect of an equipment or a strategy on the overall performance based on the physiological capabilities of the rider and external parameters. In this paper, we present results obtained from the recent realistic models for time trials developed in collaboration with a World Tour team in order to support sport directors and coaches in making the right decision in terms of strategy and equipment.
-
Modeling in Road Cycling for Optimal Pacing Strategies: Theory vs. Practice
Introduction: The right choice of a pacing strategy for a time trial race is important and often difficult to establish. With the increasing popularity of online sports data platforms like Strava (www.strava.com), pacing strategies may become interesting even for recreational cyclists since they can compete against each other virtually on selected segments. Methods are now available to generate pacing strategies that are optimal, however, only in a mathematical sense. Until now, they were tested in practice only under laboratory conditions [1]. Pacing strategies are generally based on two mathematical models: (1) to describe the relation between power output and speed [2], and (2) to describe the fatigue of the rider related to the power output [3]. The quality and validity of these pacing strategies relies on the accuracy of the predictions made by those models.In this paper, we describe our findings on a pilot study during a two week period of cycling with regard to the prediction quality of the two models while following precalculated optimal pacing strategies in the field rides. This is not meant to be a fully-fledged study applying, e.g., a statistical analysis for a sufficiently large number of participants. This pilot study rather intended to demonstrate that, in principle, the theoretically optimal pacing strategies can in fact be implemented for field rides in practice. Moreover, it was the purpose of the study to identify the problems of the approach occurring in practice, and to outline solutions for these.Methods: The physiological model is similar to the one used in [1]: an extension of the critical power (CP) concept with reduced recovery. The physical model to predict speed from the rider’s power output is taken from [4]. The optimization of the pacing strategy for an uphill time trial proceeded as in [1]. To calibrate the CP model, four tests were performed in the laboratory for a single hobbyist rider, followed by a number of rides on Strava segments with the goal to achieve personal bests by pursuing the given optimal pacing strategies.The precalculated pacing strategies were communicated during the field rides by means of a custom developed App on a smartphone mounted on the handle bar. Feedback was given numerically, e.g., the current deviation from the optimal speed, and visually by a dash board type gauge. Accumulated deviations from the optimal pacing were attempted to be corrected using a PID control mechanism. These rides were taken to update the parameters of the CP model continually.Results and Discussion: Four rides with optimal feedback were performed on three different Strava Segments. These segments were mainly climbs with a length of 3.5 to 5 km and an average grade from 5.6 to 7 %. The rider’s critical power ranged from 230 to 257 W depending on which tests were used for calibration. The feedback was followed with a root-mean-square error of 0.77 m/s in speed and 48 W in power. Modelling errors and deviations from theoptimal strategy lead to time differences at the end of the segment ranging from 15 s quicker to 100 s slower than the optimal strategy predicted.This discrepancy in time is partly explained by having short downhill parts within the segments and errors in the estimation of the slope profile, which is shown in Figure 1. In the downhill parts, the optimal strategy suggested speeds higher than those during the field ride in which additionally braking was necessary. This error could be reduced by adding a more realistic speed constraint to the optimization and consider braking in the pacing strategy.While the physiological model first was calibrated using tests with a length of about 30 min, the model prediction for the first ride on a shorter segment showed quite poor performance. Adding this segment to the parameter estimation changed the parameters in a way that critical power was reduced and anaerobic capacity increased. With this new parameter set, short as well as mid-range segments were predicted quite well. This shows how important it is to use a range of test durations that covers the future applications.Conclusions: The results showed, that the models work quite well in general and they can be applied to uncontrolled conditions when considering some limitations. Downhill parts are difficult to model and time differences between prediction and ride must be expected in these scenarios. The physiological model needs to be calibrated using segments similar in length and load to the ones that are predicted. With proper model parameter selection and visual feedback with respect to an optimal pacing strategy, significant performance gains for uphill time-trials of hobbyist, amateur, and perhaps also professional athletes can be expected. -
Muscle deoxygenation kinetics in cycling time trial
Background: Concentration changes of oxygenated and deoxygenated haemoglobin (O2Hb and HHb) measured by near infrared spectroscopy (NIRS) provides information about oxygen delivery and extraction at the muscular level. The kinetic response of HHb reflects the adjustment of the oxidative metabolism in skeletal muscle and could therefore be related to exercise tolerance. While most studies used laboratory cycling to investigate the kinetic responses, the effect of cycling time trials in field conditions remains to be shown. Therefore, the aim of this study was to investigate changes in HHb during maximal effort cycling time trials in field conditions. Methods: Thirteen trained cyclists and triathletes (N=13; mean ± SD: age 32 ± 7 years; body mass 74.6 ± 7.4 kg; stature 182 ± 5 cm; maximum oxygen uptake 67.9 ± 3.0 mL·min-1·kg-1; maximal power output 406 ± 39 W), completed 3 cycling time trials lasting 10, 4 and 1 min on a flat road, interspersed by a 30 min recovery period after each trial. Relative changes in HHb were recorded on the right vastus lateralis muscle with a portable continuous-wave NIRS device. Second-by-second data normalised to 100% of the response were used to resolve the amplitude, the time delay and the time constant by nonlinear regression. A repeated measure ANOVA was used to compare the parameter estimates across the time trial durations. Results: The mean power output during the 10-, 4- and 1- minute cycling time trials was 352 ± 45, 385 ± 49 and 525 ± 73 W, respectively (p=0.001). No significant differences were observed for cadence during the 10- vs. 1-minute cycling time trials (p=0.264), however significant differences were observed between 4- vs. 1-minute (p=0.05) The parameter estimates of the kinetic response were significantly affected by time trial duration. The amplitude for 10- vs. 1- minute (78.20 ± 8.42 vs. 89.16 ± 6.82; p = 0.022) as well as for 4- vs. 1-minute (74.99 ± 6.12 vs. 89.16 ± 6.82; p = 0.006) cycling time trial duration showed significant differences. Moreover, significant effects can be reported for the 10- vs. 1-minute time delay parameter (9.54 ± 2.07 s vs. 3.65 ± 1.71s; p = 0.001). Mean response time also demonstrated significant differences for 10- vs. 1-minute cycling time trials (13.45 ± 2.39 s vs. 6.85 ± 1.90 s; p = 0.001). No significant differences were reported for the time constant among the different cycling time trial durations (p>0.05). Discussion: These findings support that the physiological response to high intensity exercise during multiple cycling time trial durations could be monitored by alterations in muscle deoxygenation kinetic parameters. Furthermore, these results imply that changes at the microvascular level are time dependent when exposed to maximal exhaustion. However further research is recommended to support these findings of muscle deoxygenation kinetics during cycling time trial in field conditions. -
Guiding athletes through heartrate and power based tasks
Background
Structured training usually consists of tasks with fixed intensities set by, for example, heart rate or power. Additionally, tests designed for monitoring changes in training status often require athletes to keep their heart rate within one or a few beats of a certain threshold. However, these tasks can be difficult to fulfil, especially for novice athletes and even harder when the boundaries for the targets are narrow. Nevertheless, for reproducibility it is important that tasks are executed in the best possible manner. This pre-study aims to investigate which visual aids can help athletes to achieve better accuracy in their tasks.
Method
In this study two variants of a novel visual feedback were compared to a classic design showing only numbers. Figure 1 depicts the three variants of the feedback. The first variant (a) visualises the target HR and deviation from it using a horizontal bar while the second variant (b) visualises the same using a Tachometer with the target centred in the middle. The ‘classical design’ (c) visualises the current heart rate or power using a plain number. In order to test the variants a smartphone app was created using the Pegasos-Framework (Dobiasch & Baca, 2016). The app recorded heart rate as well as power and transmitted them to a server in real-time.
The test used for the evaluation of the feedback variants is a modified version of the Lambert Submaximal Cycling Test (LSCT) (Lamberts, Swart, Noakes, & Lambert, 2009). The tasks were as follows six minutes at 60% of self-reported maximal heartrate ± two beats, six minutes at 80% ± one beat and three minutes at 90% ± one beat. This was followed by 90 seconds rest. After this a pop up window on the screens tells the participants their target power during the next three minutes stage. During this stage participants were asked to keep their power within ± 10 watts of the target power. This stage was again followed by 90 seconds rest on the bike.
Each participant completed three trials each with a different version of the feedback in a randomized order. After each trial participants were asked to out a questionnaire about the used feedback variant.
Results
12 participants (8 male, 4 female. Mean ± SD; age: 33.13 ± 12.67 years, height: 178.75 ± 7.56 cm, body mass: 73.12 ± 10.97 kg) participated in the pre-study. Table 1 highlights the results from the heart rate based task. In order to account for the time needed to raise the heart rate to the desired level all measurements are taken starting from one minute into the stage. Two participants were excluded from this analysis due to non-adherence to the protocol or very low accuracy (< 20%). Furthermore, we analysed the relative time spent in the target zone. Due to technical problems, two further trials had to be excluded. Again, no significant differences between the feedback variants were found using a repeated
-
Relation between maximal power in sprint cycling, pedal force orientation and strength of the lower limb muscles in elite sprint cyclists
The aim of this study was to determine, in a high-level population, how the maximal power produced during pedalling relates to the capacity to orient the pedal force, and to the force-generating capacity of the six main muscle groups of the lower limb, and whether this relationship is improved by using specific velocity conditions during single-joint strength measurements. 19 high-level cyclists performed two separated sessions : first, maximal power during pedalling was assessed while strength capacities were assessed in different force-velocity conditions. Results suggest that assessing single-joint strength at specific velocities is more relevant, and this, particularly in the extension phase. In the flexion phase, the power produced is largely influenced by the capacity to effectively orientate the force on the pedals.
-
External training load, performance markers and body composition of professional road cyclists with-in competitive season
Throughout the competition season, exercise performance and body composition are modified depending on the specific training regime employed as to face the races schedule at the best.During the season, bioelectrical impedance analyses (BIA), weight, body circumferences, skinfold thickness measurements (7 sites), were performed on four professional road cyclists. All measurements were completed in the morning in fasting condition. Training volume and intensity were also monitored within the season. Resistance, reactance and vector length slightly increased over the season, whereas sum of skinfolds showed a slight decrease. On average, external workload did not significantly change over the course of the season. In conclusion, riders body composition improved closer the most important races for the team during the season.
-
Effects of high intensity continuous and intermittent training strategies used for endurance development on cardio-vascular responses
Purpose of the present study was to examine the potential effects of five high intensity training (HIT) models on central and peripheral components of VO2max. We analysed O2 consumption (VO2), cardiac output (Q), stroke volume (SV), heart rate (HR) and arteriovenous O2 difference (a-vO2diff) in different regimes of HIT during loading and recovery periods. Eight well-trained male competitive cyclists take part in the study (age: 22.1±3.1 years; body mass: 66.2±8.5 kg; height: 175.4±5.2 cm; body fat: 7.2%±1.1%; O2max: 64±5.61 mL∙min-1∙kg-1). Following familiarization sessions, VO2max was determined, and then, maximal SV, HR, Q and a-vO2diff (SVmax), (HRmax), (Qmax), (a-vO2diff_max) were evaluated individually using exercise intensities corresponding to 40 to 110% of VO2max separately, by nitrous-oxide re-breathing (N2ORB) method. Thereafter, training models were performed as; HIT1: 16 repetitions with power at ~110% of VO2max for 45-sec (16×45-sec, p@~110%VO2max) with 1:1 work and recovery (w/r) ratio; HIT2: 4×3-min at p@~93%VO2max with 1:1 w/r ratio; HIT3: alternating the power between VO2max (1-min) and anaerobic threshold (4-min) × 5 repetitions; HIT4: 25-min constant-load, HIT5: 6×30-sec at 7,5% body weight with 1:7 w/r ratio. All participants reached exhaustion at all tested HIT models. After the repeated-measures analyses, possible significant differences were investigated by post-hoc LSD/Wilcoxon. Tspent above 95% of VO2max was higher in HIT2 session than other exercise modalities (p<0.05). However, amongst all protocols Tspent above 90% of VO2max were not statistically different amongst exercise modalities, except HIT5 (p>0.05); Tspent at VO2max was lowest in HIT5 (p<0.05). Tspent at Qmax was higher in HIT2 and HIT3 sessions than HIT1, HIT2 and HIT5 (p<0.05). Tspent at SVmax was higher in HIT3 and HIT4 modalities than HIT1 and HIT2. Tspent at 95% of HRmax was higher in HIT2 session than other exercise modalities (p<0.05). Tspent at a-vO2diff_max was higher in HIT1 and HIT2 than HIT3, HIT4 and HIT5 (p<0.05). These results show that different exercise modalities reaching similar VO2max levels may be effective in the development of central or peripheral components associated with VO2max. It may be said that continuous HIT modalities seems to have a higher potential to improve central part of VO2max, while intermittent HIT modalities seems better for peripheral one.
-
Research and Innovation in Sport on a Budget: The MacGyver Approach
Research and innovation are necessary in high performance cycling in order to maintain competitiveness on the track, the road and the dirt at World, Olympic, and Paralympic level. Some teams are able to invest substantial sums in this work, while others have smaller budgets but still have the same performance demands. It is possible to achieve effective innovation on a tight budget by using an approach similar to the TV show “MacGyver”, where tools were made or repaired in an improvised way, making use of whatever items were at hand. Applied to sports innovation, this means identifying resources that a team already has access to, creating partnerships that benefit both parties rather than one-sided sponsorships, tapping into external experts who already have the knowledge the team needs, learning lessons from other teams, and being especially mindful of implementation. Cycling Canada has created a team of partners and experts who not only provide support for the team, but who have connected with each other to solve design and production issues. Of particular note is that all of the partners are Canadian, which lends a common purpose to the overall innovation goal. Cycling Canada is committed to providing excellent equipment and performance support to the team, as well as providing added value to the partners.
-
Kinematics, muscle recruitment patterns and pressure mapping in cycling biomechanics - Recent research findings and practical outcomes.
Objectives: With the increase in popularity of cycling, a properly configured bicycle is essential for maximizing performance and preventing injuries, whilst maintaining comfort. It has been suggested that cyclists train in the same conditions that they would race in, optimizing the muscle coordination patterns used during competition. For this reason, it is important to understand both the bicycle setup and the riders position at different intensities.
One of the key measurements conducted during bike-setups is the static or dynamic measurement of knee flexion angle. We previously demonstrated that there is a significant change in knee, ankle, hip and shoulder angle from static to dynamic measurements. This change during cycling may have an effect on the cyclists’ performance, economy and injury risk. Other factors to consider are fatigue and workload intensity, and how these may impact on the riders’ position and muscle recruitment patterns. Comparing pressure load and distribution in various saddle zones, through a range of workloads, may give a better understanding to genital discomfort and optimisation of saddle positioning.
Methods: Seventeen well-trained cyclists (Age 31±9years, Mass 75.5±7.5kg PPO 354.0±34.5) were enrolled for the study. Whole body kinematics and EMG patterns were analysed during a steady state cycle at 60% VO2 max, and at 60, 80 and 90% heartrate intensities. Saddle pressure was also recorded at 60, 80 and 90% heartrate intensity.
Results: There were no changes in body joint angles nor muscle recruitment patterns during the steady state cycle. There were significant changes in the ankle, knee, elbow, thoracic and lumbar flexion angles with increasing intensity (see Figure 1). There were also significant changes in the EMG patterns of the cyclists for all muscles except Medial Gastrocnemius (see Figure 2). The saddle pressure data demonstrated significant changes in the loaded area and mean force through different areas of the saddle.
Conclusion: As previously suggested, compensatory lower limb kinematics occur in order to maintain a given power output. For riders that will be training at these specific intensities it would be beneficial to have their bike setup done taking the kinematic changes into account.
-
Concussion assessment in cycling: a systematic review and call to action
See uploaded document -
Effects of flat and uphill cycling on the power duration relationship
Background: The power duration relationship is a powerful tool for performance diagnosis in endurance sports. It is currently unknown whether the slope of the terrain effects the estimation of critical power (CP) and the work available above CP (W´). If so, the information obtained (e.g. intensity domains) cannot be generalized for different conditions. Therefore, the aim of the current study was to investigate the effects of flat and uphill cycling on the power duration relationship. Methods: Thirteen endurance trained subjects participated in this study (mean ± SD age: 32.2 ± 7.1 years; stature: 181.8 ± 4.7 cm; body mass: 74.6 ± 7.4 kg; maximum oxygen uptake: 67.9 ± 3.0 mL/kg/min; maximum power output: 406 ± 39 W). The participants performed three time-trials (TT) of 10, 4 and 1 minutes in that order, interspersed by 30 minutes of rest in both, flat (1.0 %) and uphill (10.0 %) conditions. TTs were conducted within 10 days with a rest period of at least one day between the tests. Participants were encouraged to produce the highest possible power output (PO) and maintain a cadence between 80 and 100 revs/min during the TT. PO and cadence during each trial were recorded with a mobile power crank (SRM), which was mounted on a 26-inch mountain bike. Mean PO from the TTs were modelled using the linear 1/time model (P = W´(1/t) + CP) for each condition. With standard errors of 1.4 ± 1.0 % and 3.9 ± 2.8 % for CP and W´, respectively, and nearly perfect coefficients of determination (R2 = 0.987 – 1.000) the 1/time model showed the best fit. Paired t-tests were applied to compare the estimates of CP and W´ from flat and uphill cycling. Results: PO during the TT was significantly affected by test conditions during the 1-minute trial (526 ± 74 vs. 559 ± 70 W during flat and uphill cycling, respectively; P = 0.001). No significant differences were observed during the 10 and 4-minute trials (353 ± 45 vs. 361 ± 36 W; P = 0.071 and 386 ± 49 vs. 393 ± 42 W; P = 0.289 during flat and uphill cycling, respectively). CP was not significantly different between flat (336 ± 43 W) and uphill (338 ± 35 W) cycling (T12 = -0.677; P = 0.489), whereas W´ shows a significant difference between flat (11.4 ± 2.7 kJ) and uphill (13.2 ± 3.1 kJ) cycling (T12 = -3.626; P = 0.003). Discussion: The results of the present study suggests that the estimated CP is not sensitive to changes in gradient. However, W´ was affected by the gradient, which might be related to the significantly higher PO in uphill conditions during the 1-minute TT. Therefore, the results of the present investigation indicate that information obtained from the estimated CP (e.g. intensity domains, race targets) is unaffected by the slope of the terrain and can be generalized for different conditions. Nevertheless, individual differences for the estimates of CP and W´ between test conditions should be considered as well.
-
Identification of the threshold ambient temperature above which pre-cooling has a performance benefit for time trials in the heat
Introduction. Endurance exercise performance progressively deteriorates as the surrounding ambient temperature increases,1 which is exacerbated when combined with increasing humidity2 and solar radiation.3 It is clear that there is a strong link between increases in thermoregulatory strain, due to elevations in both metabolic and ambient heat, and impaired endurance performance.4
It has become commonplace to implement pre-cooling prior to competition to alleviate this performance decline, with ~50% of athletes having a defined strategy prior to competing in the heat.5 Such strategies include the use of ice-vests, which have been suggested to improve time trial performance in the heat by approximately 5%.6 However, little is known about the ambient temperature threshold above which pre-cooling becomes an effective strategy for enhancing endurance performance. With most studies focusing on a single ambient temperature, typically above 30˚C or a Wet Globe Bulb Temperature (WGBT) of 26˚C.7 Therefore, it was the aim of this study to investigate the effect of pre-cooling in different environmental temperatures on time trial performance.
It was hypothesized that pre-cooling would improve time trial performance in all environmental temperatures, with the magnitude of effect dependent on environmental temperature.
Methods. In an independent groups design, 24 trained male cyclists (age 24.3 ± 5.1 years; VO2max 61.3 ± 3.7 mL.kg.min-`; training frequency ≥3 times per week) completed two time trials with (COLD) and without (CON) of pre-cooling using an ice-vest and sleeves ensemble. Pre-cooling was implemented for 30 minutes at rest and during a 9 minute progressive warm up, in ambient temperatures of 24.0 ± 0.1°C & 49.5 ± 1.4% rh (WBGT 19.2°C); 27.2 ± 0.3°C & 50.7 ± 5.3% rh (WBGT 22.1°C); or 35.0 ± 0.4°C & 50.6% ± 1.3% rh (29.2°C). Participants removed the cooling vest (if warn) on completion of the warm up, prior to completing a self-paced time trial designed to last ~60 minutes when ridden at ~75% Wmax.
Results. Time trial performance was 6.2% and 2.6% faster following COLD in both 35˚C and 27˚C (figure 1A) but not 24˚C (1.2%). Magnitude based inferential statistics indicate that COLD was very likely beneficial to performance in 35˚C and likely beneficial in 27˚C and possibly beneficial in 24°C. Mean power was 2.4% 2.5% and 5.6% higher following COLD (figure 1B,C) and considered to be likely beneficial in 24°C and very likely beneficial in 27˚C and 35˚C. There was no effect of COLD on gastrointestinal temperature at any point.
Conclusions. Pre-cooling with an ice-vest and sleeves is likely to have a positive effect on time trial performance at temperatures above 24˚C, with a clear relationship between ambient temperature and the magnitude of effect of pre-cooling. These results indicate that cyclists should start to consider implementing a pre-cooling procedure prior to racing a time-trial in environmental temperatures of 24˚C and above. Importantly, utilising pre-cooling in lower ambient temperatures is unlikely to have a detrimental effect on performance at the cooling intensities used here. To the authors’ knowledge, this is the first time that a lower ambient temperature threshold has been identified above which pre-cooling has a significant ergogenic impact on performance.
-
Differences in Strength & Power profiles between Road and Time Trial cyclists
Introduction
Within the scientific literature there is little evidence available to provide practitioners with information on strength and power profiles of cyclists, resulting in a limited understanding of neuromuscular factors related to cycling performance. Information on the legs’ elastic energy utilisation, force-velocity and length-tension curves can inform training programs and aid in talent identification. Other sports where such information is more widely available have already successfully implemented this within preparation programmes (e.g. McBride et al., 1999).Methods
A total of 44 cyclists were recruited for this project, of which 15 classified in a Novice category by having no racing experience at all (age 35.5 ± 11.4 yrs; height 177.4 ± 6.5 cm; mass 77.4 ± 9.3 kg; FTP 3.28 ± 0.47 W/kg), 14 in the Road racing category as they competed for at least the past year at British Cycling Category 2 level or higher and no experience in Time-Trial (TT) races (age 35.9 ± 12.7 yrs; height 179.1 ± 6.5 cm; mass 76.6 ± 9.0 kg; FTP 3.88 ± 0.49 W/kg), and 15 in the TT category as they considered TT racing as their main competitive aim, rode in dedicated TT positions and had recently produced a 10 or 25 mile personal best of <23 or <58 minutes respectively (age 38.0 ± 9.6 yrs; height 184.0 ± 3.9 cm; mass 80.1 ±6.2 kg; FTP 3.74 ± 0.46 W/kg).Muscle function was tested through a range of tests. Jump height achieved during a squat jump (SJ) and a countermovement jump (CMJ) was used to define the balance between muscular power and elastic capacities of the legs (Kubo et al., 2000). A 20-Kg loaded jump squat (LJS) was used alongside the CMJ to provide data on the force-velocity relationship (F-V) in a multi-joint movement by calculating the theoretical peak force (Fpeak), theoretical peak velocity (Vpeak) and theoretical peak power (Ppeak) values (Cuk et al., 2014). Force plates (Kistler, Switzerland) recorded data during the jumps at 2000Hz.
Furthermore, single joint isokinetic dynamometry (Biodex, USA) of the hip and knee was conducted for a range of angular velocities (30 to 270 °/s) to capture an accurate strength profile of the relevant muscle groups. Torque-Velocity profile was quantified by determining the relative reduction in torque with increasing velocity, length-tension relationships were evaluated using the angle of peak torque at 30 °/s and relative strength was quantified as a hip/knee torque ratio.
Results
The cyclists tested showed an average jump height of 29 ± 6 cm, 25 ± 5 cm and 20 ± 5 cm for the CMJ, SJ and LJS respectively, there were no significant differences between the groups (p = 0.939). The ratio of SJ over CMJ height averaged on 0.87 ± 0.11 with competitive cyclists scoring slightly but not significantly lower (0.84 ± 0.09) than the novice cyclists (0.89 ± 0.12; p = 0.329). Calculating Fpeak, Vpeak and Ppeak from the two-load method (CMJ and LJS), produced averages of 1903 ± 472 N, 5.74 ± 4.38 m/s and 2620 ± 1581 W respectively with no significant differences between the groups (p = 0.666, p = 0.520 & p = 0.396 respectively).Dynamometry data revealed a greater hip joint torque over knee torque in flexion and extension (hip/knee ratio > 1) for all groups. This dominance was significantly less prominent in the TT group for flexion conditions (1.35 ± 0.18) compared to Road (1.56 ± 0.22; p = 0.031) and Novice (1.53 ± 0.19; p = 0.004) groups. Joint flexion torques showed non-significant trends; they were slightly higher in the knee and lower for the hip (1.43 & 2.08 Nm/kg respectively) in TT athletes compared to Road (1.35 & 2.14 Nm/kg) and Novices (1.36 & 2.22 Nm/kg) (p = 0.429 & 0.189). No differences were found for the angle at which peak torque occurred. The velocity effect on torque production was comparable between the groups. It decreased from its peak at 30 °/s, to 82 ± 11 % of that when tested at 270 °/s for knee flexion and to 61 ± 9 % for knee extension. Hip torque reduced to 66 ± 10 % and 79 ± 10 % for flexion and extension respectively, when tested at 210 °/s compared to 30 °/s condition.
Discussion
The CMJ data show that cyclists – both novice and competitive – perform poorly on vertical jumping (29 ± 6 cm) compared to strength trained (48.2 ± 2.8 cm) and even untrained individuals (33.7 ± 2.3 cm) (McBride et al., 1999). This is in line with previous research on endurance type athletes showing long-distance runners to perform inferiorly on jump tasks compared to an untrained population (27.8 ± 4.3 cm vs 37.3 ± 3.1 cm; Kubo et al., 2000). In contrast to the findings by Kubo et al. (2000), the tested competitive cyclists showed lower SJ/CMJ ratios compared to the untrained controls indicating a relatively large utilisation of elastic energy storage compared to muscular power in jump performance.Based on the dynamometry testing, it seems most plausible to suggest that the reduced hip flexion capacity in TT riders results from these muscles being disused during cycling due to the extreme hip flexion angles common in their riding positions. It could be suggested that an attempt is made to compensate for this loss in hip flexion capacity through increased knee flexors’ strength. An increased knee flexor torque in TT riders could also indicate a mechanically more effective pedalling technique on the bike, as previous literature has linked hamstring activity with increases in Index of Force Effectiveness on the bike (Bini et al., 2013). Greater separation between tested groups might have been masked due to variation in preferred bike setup within the groups, TT riders also training in road setups and novice cyclists having undergone minor adaptations through recreational cycling activities.
Based on these results, it seems appropriate to advise strength training to be tailored to the type of competition a cyclist is aiming to perform on. TT riders should focus on knee flexor strength, while road cyclists could benefit from a more balanced approach between hip and knee strength. Currently ongoing research is investigating how these strength characteristics relate to determinants of cycling performance in order to further help optimising training protocols and talent identification strategies.
References
Bini RR, Hume P, Croft J, Kilding A. (2013) J Sci Cycl, 2(1), 11-24.Kubo K, Kanehisa H, Kawakami Y, Fukunaga T. (2000). EJAP, 81(3), 181-187.
McBride JM, Triplett-McBride T, Davie H, Newton RU. (1999). J Biom, 32(10), 1021-1026.
Cuk I, Markovic M, Nedeljkovic A, Ugarkovic D, Kukolj M, Jaric S. (2014). EJAP, 114(8), 1703-1714.
-
Muscle-tendon behaviour during sprint in road cyclists: effect of the force-velocity condition
MUSCLE-TENDON BEHAVIOUR DURING SPRINT IN ROAD CYCLISTS: EFFECT OF THE FORCE-VELOCITY CONDITION.
Robin Maxime, Hauraix Hugo, Nordez Antoine, Dorel Sylvain.
University of Nantes, Laboratory “Movement, Interactions, Performance” (EA 4334), Faculty of Sport Sciences, France
INTRODUCTION: The “force-velocity” test in cycling is classically used to determine the maximal force- and power-velocity capacities of the lower limb muscles (Dorel 2018). However, the biomechanical constraints related to this multi-joint task induce a specific coordination of muscles with different architectural and anatomical properties. From recent years, ultrasound allowed to better understand the muscle-tendon interactions in vivo and to determine the contributions of tendinous tissues and contractile structures during tasks such as walking or running (Ishikawa et al. 2005). The aims of the current study were i) to describe fascicle-tendon behaviours of a mono-articular muscle: vastus lateralis (VL) and a bi-articular muscle: gastrocnemius lateralis (GL) during sprint cycling and ii) to determine whether both fascicle and muscle-tendon unit shortening velocities are influenced by the force-velocity condition (i.e. pedalling rate).
METHODS: Eleven highly trained cyclists (21.9 ± 4.5 years, 177.5 ± 4.7 cm, 67.3 ± 4.6 kg, > 12 000 km/year) performed two series of 4-s maximal sprint cycling in four isokinetic conditions on a Lode Excalibur sport (60, 90, 120 and 160 rpm), with 3 min of rest between each sprint and 20 min recovery period between both series. The muscle-tendon unit (MTU) length was obtained using anthropometric models and kinematics data (optitrack, 120 Hz). Ultrafast ultrasound was used to measure the fascicle length of VL in the first series, and GL in the second series (Aixplorer, Supersonic Imagine; 500 to 2000 Hz according to the pedalling rate). An automatic tracking method (Farris et al. 2016) allowed to obtain fascicle length (and velocity by derivative) during the entire pedalling cycle, and the tendinous tissues length was calculated as the difference between muscle-tendon unit and the horizontal length of fascicle (Kurokawa et al. 2001).
RESULTS: The behaviour of VL during its period of activity is characterized by a unique phase during which both MTU and muscle fascicle shorten (-20° to 150°, i.e. concentric mode) while tendinous tissues slightly lengthen. For GL two phases were observed: a first during the extension (0-100°) characterized by a dorsiflexion of the ankle associated with a very slight lengthening and shortening of the muscle fascicle (i.e. quasi isometric behaviour), while MTU and tendinous tissues lengthen; a second characterized by a plantarflexion (100-270°) associated with a shortening of the MTU and both the muscle fascicle and tendinous tissues (Figure 1). The ANOVA with repeated measures demonstrates a main effect of the pedalling rate on the mean MTU shortening velocity for VL (5.68, 8.48, 10.09, 13.01 cm. s-1, p<0.001) and muscle fascicle (6.83, 10.05, 13.36, 16.77 cm. s-1 for 60, 90, 120 and 160 rpm, respectively, p<0.01). Concerning GL, no effect of pedalling rate was observed on both muscle fascicle and MTU mean shortening velocities during the period of activity (Figure 2); except a lower muscle fascicle shortening velocity at 60 rpm compared to the other conditions (P<0.05).
DISCUSSION/CONCLUSION: VL and GL have different muscle-tendon behaviours during a maximal pedalling task. For VL, MTU shortening is largely related to shortening of the muscle fibres and both demonstrate a concentric contraction. Then, the increase in pedalling rate induces an important increase in muscle fascicle shortening velocity and then a decrease in force capability of the contractile component. For instance, in the maximal power output condition (i.e. 120 rpm), the mean muscle fascicle shortening velocity is 20.5 cm. s-1 (between 70 and 100°), corresponding to almost 50% of its Vmax determined during single-joint leg extension (Hauraix et al. 2017). The behaviour of GL is more complex with MTU lengthening while fascicle is quasi isometric, followed by a shortening phase of all components, highlighting the role of tendinous tissues (i.e. elastic energy storage-release process). Interestingly, this quasi isometric behaviour may not be influenced by pedalling rate. This is explained by the decrease in the ankle range of motion and length change of the fascicle at high pedalling rates, which can be interpreted as a strategy to limit the increase in shortening velocity and continue to transmit the force to the pedal. These findings have important consequences to better understand the knee and ankle muscle-tendon behaviours during cycling and can help us in orientating strength training routines for cyclists.
Keywords: Force-velocity relationship, Fascicle-tendon interactions, Ultrafast ultrasound, cycling task.REFERENCES:
- Dorel et al., 2018. Mechanical Effectiveness and Coordination: New Insights into Sprint Cycling Performance. Biomechanics of training and testing.
- Farris, D. J., & Lichtwark, G. A. (2016). UltraTrack: Software for semi-automated tracking of muscle fascicles in sequences of B-mode ultrasound images. Computer methods and programs in biomedicine, 128, 111-118.
- Hauraix, H., Dorel, S., Rabita, G., Guilhem, G., & Nordez, A. (2017). Muscle fascicle shortening behaviour of vastus lateralis during a maximal force–velocity test. European journal of applied physiology, 117(2), 289-299.
- Ishikawa, M., Niemela, E., & Komi, P. V. (2005). Interaction between fascicle and tendinous tissues in short-contact stretch-shortening cycle exercise with varying eccentric intensities. Journal of Applied Physiology, 99(1), 217-223.
- Kurokawa, S., Fukunaga, T., & Fukashiro, S. (2001). Behavior of fascicles and tendinous structures of human gastrocnemius during vertical jumping. Journal of Applied Physiology, 90(4), 1349-1358.
-
The use of Heart Rate Variability to optimise acute and chronic training loads and recovery in recreational and elite cyclists
Heart rate variability analysis (HRV) has been established in clinical settings for several decades as an indication of acute and chronic physiological and mental stress.
Adoption of HRV is quite widespread and study outcomes generally supportive, yet controversy still exists as to the reliability of HRV for identifying NFOR and overtraining. The reasons for this include uncertainty about the physiological origin of the different types of heart rate variation, issues around the relationship between HRV and training loads, and ambiguities in regard to the interpretation of HRV data. Despite a standardisation Task Force being established in 1996, there remain uncertainties about what constitutes best practice with respect to measurement conditions and signal processing. This presentation will look at possible reasons for this controversy and consider case studies in both elite and recreational cyclists that may be instructive in identifying where and when HRV analysis is most effective and useful. Recommendations for best practice will also be provided.
Since 2009, HRV measurement technology has been available to smartphone owning athletes and their coaches using apps together with affordable ECG & pulse sensors. When measured regularly in athletes, HRV can be a useful early indicator of viral and bacterial illness, Non-Functional Overreaching (NFOR), and adaptations in response to a series of training loads. -
Training Prescription guided by HRV in cycling
PURPOSE:Road cycling is a sport with extreme physiological demands. Therefore, there is a need to find new strategies to improve performance. Heart rate variability (HRV) has been suggested as an effective alternative for prescribing training load against predefined training programs. The purpose of this study is to examine the effect of training prescription based on HRV in road cycling performance.
METHODS:Seventeen well-trained cyclists participated in this study. After an initial evaluation week (EW), cyclists performed 4 baseline weeks (BW) of standardized training to establish their resting HRV. Then, cyclists were divided into two groups, a HRV-guided group (HRV-G) and a traditional periodization group (TRAD) and they carried out 8 training weeks (TW). Cyclists performed two EW, after and before TW. During the EW, cyclists performed: (1) a graded exercise test to assess VO2max, Peak power output (PPO) and ventilator thresholds with their corresponding power output (VT1, VT2, WVT1, and WVT2, respectively) and (2) a 40-min simulated time-trial.
RESULTS:HRV-G improved PPO (5.1 ± 4.5 %; p= 0.024), WVT2 (13.9 ± 8.8 %; p= 0.004) and 40TT (7.3 ± 4.5 %; p= 0.005). VO2max and WVT1 remained similar. TRAD did not improve significantly after TW. There were no differences between groups. However, magnitude-based inference analysis showed likely beneficial and possibly beneficial effects for HRV-G instead of TRAD in 40TT and PPO, respectively.
CONCLUSIONS:Daily training prescription based on HRV could result in a better performance enhancement than a traditional periodization in well-trained cyclists.
-
Predicting a Power-Duration Curve in Elite Endurance Track Cyclists.
Keywords: Power-duration, performance modelling, track cycling.
Introduction
A power-duration curve provides coaches and athletes with a snapshot of the workload achievable for any given duration at a single point in time which can then be used to inform training and race strategy depending on the demands of the event. The accuracy of a power-duration curve is important to ensure it can be used to accurately predict performance. This preliminary research aims to determine whether a multi-trial protocol can be used to accurately predict the power duration curve up to the length of 20 minutes (to reflect the longest trial that is usually used) whilst incorporating an accurate prediction of the athlete’s capabilities within the severe exercise domain (typically durations shorter than 60 seconds). Furthermore, this research seeks to explore which trials can be used to most accurately predict the curve with the least amount of trials so that coaches and athletes can use the protocol without impacting heavily on their training schedule. This research has been conducted using elite track cycling endurance athletes who are typically able to achieve greater power outputs within the severe exercise domain than an elite road racing cyclist however they must still demonstrate strong aerobic capabilities to race for longer durations than a track sprint cyclist therefore this research also demonstrates the challenges in predicting a power-duration curve in a novel subject group.
Methods
A total of 20 (11 male, 9 female) elite track cyclists (defined as having competed for a National Cycling Federation at a major international competition within the last 2 years) aged 22±4 years completed 6 maximal time trials of differing durations (6 seconds(s), 30s, 60s, 360s, 720s, 1200s) over 2 days (3 on each) on a static cycle ergometer (Wattbike, Nottingham UK). The combination of the trials was randomized for each day but the participants always completed the trials in reverse time order. Each trial was completed seated and from a static start using the participants same individual riding positions. Participants were asked to refrain from strenuous activity for 24 hours before the trials and had 30 minutes of off the bike recovery between the 3 trials on each day and 24 hours of recovery between the two testing days to ensure they could perform their best in each trial.
The average power output was recorded for each of the 6 trials completed and plotted on a power duration curve (Figure 1). Individual data points were then systematically taken out of the power duration curve to determine whether an accurate prediction could still be achieved with less trials (Figure 2). For each combination of trials, all the known power outputs (6s, 30s, 60s, 360s, 720s,1200s) were compared to the predicted power output. Figure 1. Power-duration curve predicted using 6 maximal time trials over a 2-day period. Figure 2. Power-duration curves predicted from the same data set using 2,3,4 and 6 data points. ResultsProtocol Key
Black
All 6
Green
6 360 1200
Yellow
30 360 1200
Red
6 60
Blue
360 1200
Protocol
Black
Green
Yellow
Red
Blue
Time (S)
6
0.0005
0.0005
0.0005
0.0005
0.0005
30
0.0005
0.0005
0.0005
0.0005
0.0005
60
0.0005
0.002
0.0005
0.333
0.0005
360
0.0005
0.0005
0.0005
0.583
0.139
720
0.317
0.544
0.811
0.0005
0.817
1200
0.0005
0.0005
0.0005
0.0005
0.355
Statistical analysis showed there to be only one known duration that could be accurately predicted by the 6 and 3 point protocols and two and three for each of the two point protocols (table 1) although each of these predicted the known points included in them due to an R value of 1.0. Based on this analysis, none of the protocols tested could be used to accurately predict most the known power-duration values. Table 1. Significance values of differences between predicted and actual power output. LimitationsThe results presented were calculated using an exponential line of best fit with an R value greater than .98 however this meant that the line often under-predicted power values known to be achievable even when that duration was included in the protocol. Further analysis will amend the line of best fit to go through the highest known values.
So far, Paired T-tests were used to compare known power values for each duration tested against the predicted value from each protocol however this doesn’t provide a full representation of the power-duration curve, further statistical analysis is needed to determine whether any of the protocols demonstrate no significant difference across the whole line. -
Effects of cycling shoe cleat position in performance and physiological variables during cycling and subsequent running in simulated Olympic distance triathlon
Keywords: 1st metatarsal head, Antero-posterior cycling cleat position, Pacing
Background: A proper intervention at the foot-shoe-pedal interface in cycling could optimize lower limb kinematics, improving health and performance (Belluye and Cid 2001). It has been established that the 1st metatarsal head must be positioned directly above the pedal spindle (Belluye and Cid 2001). But the triathlon, which combines swimming, cycling and running, has specific characteristics in terms of biomechanical and physiological responses and a backward cleat position could be more appropriate on subsequent running in a triathlon at constant load (Paton and Jardine 2012). However, the legal drafting in Olympic distance triathlon leads to a great variability in crank power output production (PO) (Bernard et al. 2009). Another study which has simulated draft-legal triathlon did not observe any benefits with an aft cleat position, whether for cardiovascular cycling or running performance. However, the authors have reported a change of running pacing and particularly a faster running speed during the 1st kilometer with the traditional 1st metatarsal cleat placement (Viker and Richardson 2013). The purpose of this study was to determine the impact of the antero-posterior shoe cleat position in performance and physiological parameters during the cycling and running phases of a simulated Olympic distance triathlon.
Methods: Eight well-trained triathletes (6 males and 2 females) volunteered for this experiment (Mean ± SD: 22 ± 11 years old, 1.73 ± 0.09 m, 60.8 ± 7.7 kg). The participants performed three experimental tests within two weeks. Firstly, they completed an incremental cycling test until exhaustion to determine the maximal aerobic crank power output production (MAP) and the maximal oxygen consumption (VO2max). Then, they did a cycle-run protocol simulating the intensity of a draft-legal triathlon with two cleat positions in a random order (Table 1). The forward cleat position (FCP) positioned the center of the cleat 5 mm in front of the 1st metatarsal and the backward cleat position (BCP) placed the center of the cleat 5 mm behind the 1st metatarsal. The cycling tests were performed on a Wattbike® cycle ergometer (Wattbike Pro, Nottingham, UK) allowing to control the break resistance and the running tests were made on a standard treadmill® (Tunturi T90, Tunturi New Fitness BV, Almere, Netherlands). The VO2 was collected during cycling and running with an Oxycon-Pro® system (Oxycon-Pro, Erich Jaeger, Germany) and the energy cost (C) was calculated for the running tests (Di Prampero 1986). The cycling PO was measured with the Wattbike® and the running distance with the treadmill. Pairwise Wilcoxon tests were used to establish statistical differences between means. Statistical significance was set at p < 0.05.
Table 1: Cycle-run protocol
Cycling
Transition
Running
FCP
32 minutes divided into 8 sections of 4 minutes
1 minute
Maximum distance over 20 minutes
3’30 at 50-75% of MAP and 80 rpm
30” at 100-200% of MAP with free pedalling cadence
BCP
32 minutes divided into 8 sections of 4 minutes
1 minute
Maximum distance over 20 minutes
3’30 at 50-75% of MAP and 80 rpm
30” at 100-200% of MAP with free pedalling cadence
Results:
Table 2: Mean of performance and physiological parameters during cycling and subsequent running according to the cycling cleat position
Cycling
Running
Total
1st section of 5’
Total
FCP
BCP
p
FCP
BCP
p
FCP
BCP
P
% of MAP
70.4 ± 8.6
66.8 ± 5.9
> 0.05
Distance (meters)
1190 ± 150
1150 ± 100
> 0.05
4960 ± 540
4910 ± 480
> 0.05
% of VO2max
65 ± 3.9
59.7 ± 6.7
< 0.05
68.8 ± 11.0
60.9 ± 10.9
> 0.05
75.6 ± 8.8
65.2 ± 15.6
> 0.05
C (mlO2.km-¹.kg-¹)
147.5 ± 22.8
127 ± 34.7
< 0.05
Table 2 shows a significant decrease of oxygen consumption with the BCP during the cycling part of the test. However, we can notice a slight decrease of PO with the BCP but no significant. During the subsequent running, the performance was better while the FCP condition, and particularly during the 1st section (40 m) but no-significant. This improvement was coupled with a no-significant increase of VO2, which could explain the gain of performance. However, the C was significantly higher during the FCP condition compared to the BCP condition.
Discussion: For cycling, our results suggest that the BCP is more economical despite a no significant decrease of performance. It has been reported that a forward 1st metatarsal cleat position could lead to overuse injuries (Belluye and Cid 2001). Thereby, a 1st metatarsal or a slightly aft cleat placement could be more suitable for performance and injury prevention in cycling. Despite a performance improvement with the FCP during the subsequent running, the BCP was significantly more economical, which could be caused by a muscular economy (Paton and Jardine 2012). Moreover, the pacing was different with a faster 1st running section with the FCP, which is in agreement with previous study (Viker and Richardson 2013). In conclusion, our results suggest that a 1st metatarsal or a slightly further backward cleat placement would be more appropriate for cycling and subsequent running economy in Olympic distance triathlon despite a better performance (but no significant) with the FCP.
Acknowledgements: Morphologics Company.
References:
Belluye N, Cid M. (2001) [Biomechanical approach to modern cycling, data from the literature] Approche biomécanique du cyclisme moderne, données de la littérature. Science & sports 16(2):71-87.
Bernard T, Hausswirth C, Le Meur Y, Bignet F, Dorel S, Brisswalter J (2009) Distribution of power output during the cycling stage of a triathlon world cup. Medicine & Science in Sports & Exercise 41(6):1296-1302.
Di Prampero PE (1986) The energy cost of human locomotion on land and in water. International Journal of Sports Medecine 7(2):55.
Paton CD, Jardine T. 2012 The effects of cycling cleat position on subsequent running performance in a simulated duathlon. Journal of Science and Cycling 1(1):15.
Viker T, Richardson MX. (2013) Shoe cleat position during cycling and its effect on subsequent running performance in triathletes. Journal of sports sciences 31(9):1007-1014.
-
Estimate Power without Measuring it: a Machine Learning Application
Power is the core metric of performance in cycling. Trainers strive for maximizing it while engineers strive for minimizing its loss by improving equipement and aerodynamic drag. However, costly and specific equipments are required to optimize this process. Here, we show that power can be estimated from side data without the need to acquire power data itself. More specifically, we show a proof of concept that machine learning can serve to estimate metrics with limited equipment or missing data. In this work, we limit the scope at estimating power but aerodynamic drag could be estimated in the same spirit.
-
The effect of carbohydrate mouth rinse on physical performance during a 24.5 km cycling time trial
The purpose of the present study was to examine the effects of carbohydrate mouth rinse on physical performance during a 24.5 km cycling time trial. Twenty trained cyclists (41.0±10.5 years; 76.9 ± 7.9 kg of body mass) performed two indoor trainer cycling time trials in a randomized, placebo-controlled double-blind and crossover experimental design. In one occasion participants mouth-rinsed a 6.4% carbohydrate mixed solution (CHO) and in other occasion participants rinsed with a taste-matched placebo (PLA) for 5 seconds each 12.5% of total completion of the trial. During the trials, participants were instructed to perform as fast as possible at a self-chosen pace. Time, cycling power output and ratings of perceived exertion were obtained during the trial. There were no statistical differences in the time employed to complete the distance with CHO and PLA (2941 ± 391 vs 2986 ± 383 s; p = 0.252, respectively) with an effect size (ES) of 0.12. Similarly, average power output during the trial presented no difference between treatments (223.8 ± 50.69 vs. 218.4 ± 47.3 W, p = 0.280; ES = 0.12). CHO was ineffective to improve climbing power output (241.6 ± 45.5 vs. 234.1 ± 42.6 W, p = 0.116; ES = 0.18), peak power output during the sprint (729.4 ± 270.5 vs. 695.8 ± 235.4 W, p = 0.375; ES = 0.14) and the ratings of perceived exertion (16.00 ± 1.34 vs. 15.35 ± 1.76, p = 0.061; ES = 0.37%). Mouth rinsing with a carbohydrate solution did not improve physical performance during cycling time trial in trained male cyclists.
-
Pre-exercise optimisation of the alkalosis response to sodium bicarbonate ingestion: have we been missing its peak ergogenic effect?
The use of sodium bicarbonate (NaHCO3) as an ergogenic aid has been widespread in athletic populations where high intensity, relatively short duration activity, is an important component of performance. The traditional ingestion time for this pre-exercise ergogenic buffering agent, is typically between 60-120 minutes before the start of exercise, using the most frequently ingested dose of 300 mg.kgBM-1 (McNaughton et al., 2016). This strategy has provided some equivocal data regarding the efficacy of the use of NaHCO3, in some sporting activities (Carr et al., 2012). However, a recent innovation using a personalised approach to the pre-exercise ingestion timing for NaHCO3 (Miller et al., 2016; Sparks et al., 2017), may be more appropriate to achieve optimal ergogenic effects. The use of this technique has been shown to produce repeatable acid-base (Gough et al., 2017a) and performance responses (Gough et al., 2017b). More specifically, an individualised approach that synchronises the start of exercise with peak HCO3 concentrations, appears to produce more consistent performance advantages over placebos in exercise bouts like 4 km cycling time trials (TT). This approach still suggests that doses of 300 mg.kgBM-1 are likely to be more ergogenic than 200 mg.kgBM-1 ones, but the associated gastrointestinal (GI) side effects that are exhibited in some athletes using higher doses may be ergolytic in extreme cases (Deb et al., 2018). Indeed, the GI symptoms are both difficult to predict and may vary between trials even with normal pre-exercise experimental dietary controls in place. Athletes, coaches, and performance nutrition professionals should therefore be aware of the potential ergogenic effect of NaHCO3, when individual time to peak has been accurately established, because it is likely larger than previously observed. However, caution and careful familiarisation with this ergogenic aid is essential to determine the severity of the potential ergolytic side effects that may preclude athletes from using it.
Keywords: Ergogenic aid, performance, nutritional intervention, supplement.
References
Carr AJ, Slater GJ, Gore CJ, Dawson B, Burke LM (2012) Reliability and effect of sodium bicarbonate: buffering and 2000-m rowing performance. International Journal of Sports Physiology and Performance 7 (2):152-60. doi: 10.1123/ijspp.7.2.152
Deb SK, Gough LA, Sparks SA, McNaughton LR (2018) Sodium bicarbonate supplementation improves severe-intensity intermittent exercise under moderate acute hypoxic conditions. European Journal of Applied Physiology 118 (3):607-615. doi: 10.1007/s00421-018-3801-7.
Gough L, Deb S, Sparks SA, McNaughton LR (2017a) The Reproducibility of Blood Acid Base Responses in Male Collegiate Athletes Following Individualised Doses of Sodium Bicarbonate: A Randomised Controlled Crossover Study. Sports Medicine 47 (10):2117-2127. doi: 10.1007/s40279-017-0699-x.
Gough L, Deb SK, Sparks SA, McNaughton LR (2017b) The reproducibility of 4 km time trial (TT) performance following individualised sodium bicarbonate supplementation: a randomised controlled trial in trained cyclists. Sports Medicine Open 3 (1):34. doi: 10.1186/s40798-017-0101-4.
McNaughton LR, Gough L, Deb S, Bentley D, Sparks SA (2016) Recent developments in the use of sodium bicarbonate as an ergogenic aid. Current Sports Medicine Reports 15 (4):233-44. doi: 10.1249/JSR.0000000000000283.
Miller P, Robinson A, Sparks SA, Bridge CA, Bentley D, McNaughton LR (2016) The effects of novel ingestion of sodium bicarbonate on repeated sprint ability. Journal of Strength and Conditioning Research. 30 (2): 561-568. doi: 10.1519/JSC.0000000000001126.
Sparks SA, Williams EL, Bentley D, Bridge CA, McNaughton LR (2017) Sodium bicarbonate ingestion and individual variability in time to peak pH. Research in Sports Medicine 25 (1):58-66. doi: 10.1080/15438627.2016.1258645.
-
EFFECT OF MOUTAIN BIKE SPIRGRIPS® ON TRANSMISSIBILITY OF MECHANICAL VIBRATIONS, PERCEIVED COMFORT, MUSCULAR ACTIVITY AND HAND GRIP FORCE
Background: Prolonged mountain biking can involve pain complain in the wrists due to the ulnar nerve compression when using traditional grips (Capitani et al., 2002; Eckman et al., 1975). This phenomenon seems to be amplified by mechanical vibrations that are largely encountered during MTB practice despite the use of damping systems located in the fork and/or the frame. Recently, SPIRGRIPS® (SG) have been designed to correct the position of the hands of the user naturally by aligning the joints of his forearms correctly which is not the case with traditional grips.
Purpose: The aim of this experimental study was to evaluate the effect of SG on transmissibility of mechanical vibrations, perceived comfort, muscular activity and hand grip force during a prolonged pedalling exercise.
Methods: Sixteen trained cyclists without SG experience (age: 27 ± 10 years; height: 178 ± 6 cm; mass: 70 ± 7 kg) volunteered to participate in the study. Each participant performed a one-day laboratory cycling test on an aluminium hardtail mountain bike (Merida, Taiwan, Taiwan) equipped with a wireless SRM crank powermeter (Schoberer Rad Messtechnik, Fuchsend, Germany; accuracy ± 1%). The rear wheel of the bike was fixed onto an electromagnetic-braked ergometer (Elite, Fontaniva, Italy) while the front fork of the bike was connected to an electrical motor by a mechanical pivot.
The test included two 20-minutes pedalling sessions at ~200 W that were separated by 20-minutes of passive recovery. Each pedalling session contained two pedalling periods of 9 minutes with fork vibrations interspersed by 2 min of pedalling without fork vibrations. Mechanical vibrations delivered by the motor were characterized by vertical acceleration from 12 to 53 m.s-2 and vibration frequency from 4 to 17 Hz. Participants had to keep their hands on the traditional grips (TG) or on the ergonomic SG throughout the pedalling session. All the subjects reported their ratings of perceived comfort (RPC) on a visual numeric scale graded from 0 (very much uncomfortable) to 10 (very much comfortable) approximately 10 seconds before the end of pedalling bout. Mechanical vibrations were simultaneously measured at 1350 Hz on the mechanical pivot of the ergometer and the right wrist of the rider by two Hikob Fox inertial measurement units (HIKOB, Vileurbanne, France). Surface EMG activity of flexor carpi radialis (FCR), extensor digitorum (ED) and triceps brachii (TB) were continuously measured by Trigno sensors (Delsys, Boston, USA) which are composed of two dry bar electrodes (1 mm x 10 mm) spaced by 10 mm. Maximum voluntary grip force (MVGF) of right hand was measured by an electronic force transducer one minute before and one minute after each pedalling session. Statistical analysis was assessed by paired t-test (MVGF) and two way (grips x vibration frequency) repeated measured ANOVA (RMS of EMG and vertical acceleration data) by Statistica (Statsoft, Tulsa, USA).
Results: While MVGF decreased by 7% after pedalling exercise with TG (p < 0.05), no significant change in MVGF was found with SG. Transmissibility of vertical acceleration to the wrist was higher with SG when vibration frequency exceeds 8 Hz (Figure 2), but the difference with the TG was only significant at 17 Hz. EMG activity of FCR and TB muscles was lower with SG, notably for the highest vibration frequencies (12 and 14 Hz). RPC was not significantly different between the two grips whatever the vibration frequency.
Conclusion: This study showed that the use of MTB SPIRGRIPS® decreases fingers flexor and elbow extensor muscle activity while increasing vibration transmissibility to the wrist. In addition, maximum voluntary grip force was not altered after a prolonged pedalling exercise with vibrations. Therefore, these ergonomic grips would be interesting for mountain bikers to keep force reserve in hand and forearm for braking in steeper downhill and/or driving bike in technical sections.
Acknowledgment : The authors would like to thank Pascal Badollet founder of SPIRGRIPS®, for his technical helpful.
References:
Capitani D et al. (2002). Handlebar palsy – a compression syndrome of the deep terminal motor branch of the ulnar nerve in biking. J Neurophysiol 249(10):1441-1445.
Eckman PB et al. (1975). Ulnar neuropathy in bicycle riders. Arch Neurophysiol 32(2):130-132.
-
The effect of time trial position on physiological variables in elite cycling.
Introduction
Improving time trial performance can be achieved by cycling with an optimized aerodynamic position1. However, although reducing the cyclist’s frontal area will reduce the air resistance that must be overcome, a time trial position has significant flexibility requirements and some positions can potentially impair the ability to produce external power2. Physiological effects of using an aerodynamic position compared to an upright one, such as increased oxygen cost, have been shown in recreational cyclists2. In competitive cyclists, on the other hand, no difference between using the drops compared to an upright position has been shown3. However, less is known about the effect of these position changes in cyclists at the highest level, as well as the effect of using a too low position. Therefore, the purpose of the present pilot study was to investigate the effect of different time trial positions on physiological variables in elite competitive cyclists.
Methods
Three male junior elite cyclists participated in the study. All participants were competitive at the national level and participated in the national championships. Three positions on the bike were used: a high and low time trial position and an upright position with straight arms holding on the base bars. Each bout lasted 5 minutes, was separated by 4 minutes of rest and the work rate was set relative to the individual level of each cyclist, at ~90% of their 20-min peak power. All cycling was done at freely chosen cadences on a time trial specific bike mounted on a trainer (Computrainer LabTM, Race Mate, Seattle, WA, USA).
Results
Average work rate during the cycling bouts was 339±16W (4.7±0.2 W/kg). The physiological response of cycling in the three positions is presented in Figure 1. The lowest time trial position resulted in higher blood lactate levels, higher oxygen consumption and lower gross efficiency compared to the high time trial position. For the upright position, oxygen consumption and gross efficiency were comparable to the lowest time trial position. However, blood lactate during the upright position was the lowest measured across all conditions.
Discussion
The main finding of the present study was that using a very low time trial position led to decreased gross efficiency and increased oxygen consumption and blood lactate compared to the high time trial position. The upright position led to an increased oxygen consumption compared to the time trial positions, but blood lactate was lower, which could indicate an increased energetic cost of maintaining an upright position with the arms. The reduced gross efficiency and increased blood lactate further indicate that in elite level junior cyclists, having a too low time trial position may be physiologically unfavourable. -
Anthropometry, physical fitness, and coordination in young cyclists of different disciplines
Knowledge about general and sport-specific characteristics is currently limited to adult professional cyclists from different disciplines. However, it is unknown to what extent these performance features are already present and reliably measurable in young and adolescent riders. Pion et al. (2014) have shown the relevance and discriminating character of the use of a general multidimensional test battery in young sporting populations, rather than sport-specific (due to trainability) and physiological tests (due to physiological adaptations during childhood and adolescence) [1]. Moreover, it was found that the profiles of athletes are very similar at young age and diverge after several years into talent development programs [2]. Early diversification is therefore suggested especially in late specialization sports such as cycling, but this does not alter the fact that the young athletes may already prepare themselves in the discipline that suits him/her the most. Consequently, the first aim of the present cross-sectional research is to obtain reference values for young and adolescent cycling athletes. The second purpose is to investigate if young talented athletes from the five selected disciplines, can be differentiated from each other based on a multidimensional test battery.
A total of 332 male cyclists (7-11yrs: N=118; 12-16yrs: N=214), selected by qualified coaches, participated in the study. Athletes from bicycle motocross (BMX), road cycling, road + cyclo-cross, road + track and mountainbike (MTB) performed a test battery consisting of four anthropometric, seven physical, three motor coordination tests, and one cycling-specific test. A MANCOVA (maturity as covariate) was conducted to examine differences between the cyclists from the different disciplines based upon the generic test battery scores.
MANCOVA revealed significant differences between the disciplines for the physical performance tests. BMX cyclists jumped further and were significantly faster on the sprint test than most of the other disciplines. The road cyclists were faster on the 30m sprint than the others with exception of BMX. In the older age group the different cycling disciplines can be differentiated from each using a general multidimensional test battery. BMX cyclists had a significantly higher BMI and outperformed the others based on the SBJ, sprint test, the jumping sideways (motor coordination) and maximal cadence (cycling-specific) test. BMX and MTB riders also tended to score better on the balance beam test.
The present study is the first to document the athletic profile of young and adolescent cyclists from five different cycling disciplines. The profiles are similar at young age especially for the cycling disciplines where peak performance is achieved at later age. Within this population, it is suggested to stimulate early diversification and participation in multiple disciplines within cycling. BMX, in which athletes reach peak performance at early age, is the only discipline that can be differentiated from the others based on physical performance characteristics at young age. In the older age group, the athletic profiles become more distinguishable from each other, and differences are found for anthropometric, physical, motor coordination and cycling specific test(s). Although further research is warranted, these results suggest that the athletic profiles of the different cycling disciplines at young and adolescent age are considered to be complementary. This is a valuable finding in the discussion on early/late specialization and talent orientation.
-
Physiological response to cycling with variable versus constant power output
IntroductionVariable power output (VP) is one of the main characteristics of a road cycling mass-start. Executing a strategy with variable power during a time-trial also leads to a better finishing time than a strategy with constant power output (CP) when external conditions are not constant. Thus, tolerating VP during outdoor road cycling highly influences performance. Although physiological response to VP and CP has previously been investigated, there is a lack of continuous and comprehensive measurements during these two power conditions. To the author’s knowledge, no previous studies have investigated this in a cohort of elite competitive cyclists, nor at an intensity corresponding to low-intensity (LIT). Accordingly, the aim of the present study was to investigate physiological response to VP vs. CP as well as the perceived exertion of these two power conditions, and to investigate if variations in power output which span above lactate threshold (LT), differ from variations below LT.
Methods15 elite competitive cyclists (mean ± SD: age 24.9 ± 7.6 years, VO2max72.9 ± 5.1 ml/kg/min). During the season prior to this study, they participated in 34 ± 17 races. All of them participated in the national championships, whereas seven of them participated in UCI 1.2 category level or higher. They completed three test days, including one day of baseline testing and two days of main testing, consisting of four bouts of 28 min at two different intensities with VP and CP. The two intensities were termed “low” and “high”, where the average intensity was 70 % of LT and 95 % of LT, respectively. VP was performed with a ± 15 % fluctuation of the average power output every second minute. The four bouts that the subjects went through were low constant (LC), low variable (LV), high constant (HC) and high variable (HV). Oxygen consumption (VO2), respiratory exchange ratio (RER), heart rate (HR), blood lactate (LA), rating of perceived exertion (RPE), cadence (RPM) and workload (W) were measured
ResultsThere was no significant difference in average power output between LV and LC (233 ± 20 W), nor between HV and HC (290 ± 20 W). At both low and high intensity, the VP condition induced a significantly higher VO2and LA than the CP condition did. RPE was similar between power conditions at high intensity. Additionally, at the high intensity, cycling with VP led to a greater increase in LA and lesser increase in RPE compared to cycling with CP.
Discussion/conclusion The results of this study show that, despite considerable differences in the demand during the VP and CP bouts, there are minor differences in physiological response to these two power conditions in a cohort of elite competitive cyclists. Since VP may, in many cases, be a more race specific training method than CP, and the fact that varying power not was reported to be more exhausting than maintaining a constant power, a practical implication of these findings is that training with VP seems to be a viable alternative to training with CP, at least at high intensity.
-
A critical confusion
The critical power concept was first proposed by Monod and Sherrer in prehistorical times of performance analysis. Critical power CP was defined as the power limit between easy (non-fatigable) and hard (fatigable) exercise. The second parameter of the model, W' is the total amount of work that can be achieved in a continued effort at power levels in excess of CP. As per definition an effort below or at CP can be sustained without duration limit.
In order to measure these parameters CP and W' a multiple exhaustion (MEx) protocol was developed in the mid 80's. The testing subjects were instructed to ride at constant power levels between 85 % to 105 % of their individual VO2max power. The corresponding exhausting duration ranges between 2 and 12 minutes. A (1/T,P) plot of power versus the inverse of duration yields a straight line from which CP and W' are extracted. More recently an alternative 3-minute all-out test is used. The subject is instructed to start sprinting and to sustain highest possible effort during 3 minutes. Power level during the last 30 seconds is considered to be CP.
CP as determined by any of these protocols is unable to explain or predict performances that elucidate sustainable durations longer than 20 minutes, i.e. long TT or climbing stages in the Grand Tours
Therefore many authors have erroneously re-defined CP as being the power limit between "hard" and "extreme" exercise and accept sustainability durations of less than 20 minutes.
This unfortunate duality leads to confusion, misunderstanding and to inability to predict performances in the climbing stages of grand tours TDF, Giro, Vuelta.
Proper analysis of power-duration field data i.e. Mean Maximal Power, or Power Profile are preferable.
Examples of long sustainability in climbing stages are shown for various top-10 riders of the 2013-2014 TDF. The absolute top class achieves CP-values of ~ 5.4 W/kg and W' ~ 0.9 - 1.5 kJ/kg
The short-long duality is illustrated by simple (1/T,P) plots of the 1 year MMP data of World Tour cyclists. In all cases two straight line segments are identified. We conclude to introduce a (CPs , Ws') as critical power and anaerobic work for short efforts (from ~2' to ~15'), together with (CP, W') as critical power and anaerobic power for intermediate and long efforts (from ~15' to 120' or more). The intersection of both linear segments occur at supercritical power SCP which is the real treshhold between exercises at hard and extremely hard intensity..
Because exhaustion occurs at or near depletion of either W' or Ws' it is also interesting to monitor the depletion-recovery state of a cyclist after a ride, or live during the ride. The near future may even bring us on-bike power meters with exhaustion indicators.
